Maestro Van going for Scrap - Anyone need anything

[E_T_V]

Sadly the time has come for me to strip and scrap my maestro campervan. It has served me well these past 4 years, but its number is up and its off to the crusher.

Does anyone need anything?
I can't promise to remove everything asked for as time is short but I'll try and help out. If you want to come and collect/strip then that is fine (assuming that I don't need that bit!).

Its located in the north of sheffield. Small parts I'll keep till the shows or will post. Prices are going to be very reasonable. Engine is spoken for for a member on here. Some other parts are detined for my next project vehicle.

Let me know what you are after.

[D813YBB]

I'm still looking for a front passenger side seat belt stalk in dark grey...

[E_T_V]

No problem. Its the standard grey from the mk 2 interiors as far as I know (J reg van).
PM me an address and I'll remove and package it up. Does a quid plus postage sound ok?

[Guest]

Dan, anything you don't want I will gladly take off you!

Are the rear bumpers spoken for? Standard van wheel trims/centres?

[E_T_V]

Rear bumpers I'm not sure about, I know they are a little rusty. If they are any good and the ones on my newer van are fine then you can have them along with the other bits.
I've got lots of van wheels you are welcome to but no wheel centres sadly.

[Guest]

Whats the next project Dan?

Another Maestro? or maybe a Monty this time?????


Mal.

[E_T_V]

Another maestro of course! What else??

[Guest]

I have a TD that could do with a nice new owner!

Mal.

[D813YBB]

Dan

email sent regarding seatbelt item.

[E_T_V]

no probs, I'll get in in the post after the weekend probably.

[MAESTRO_MONTEGO]

DAN,do want a van project?
as my diesel van has to go this month

[Guest]

Id like to have the front uprights, how much are they?
also whats the PCD? maybe also the driveshafts depending on cost
tel; 07749119626

[E_T_V]

DAN,do want a van project?
as my diesel van has to go this month

No offence intended but the van I am scrapping is probably in better nick than your one!

I've already got one van project on the go thanks!


I'm keeping the front struts on my existing van (about a year old) to swap onto my new van but the ones on my new van are up for grabs if you want them, (ledbury ones with a fair few miles on them). The hubs both have new bearings (4.5 inch pcd), but the hubs are still noisy so I'll not guarentee them. Driveshafts I'll be keeping for the project as they are refurbed recently.

[MAESTRO_MONTEGO]

No offence intended but the van I am scrapping is probably in better nick than your one!

I've already got one van project on the go thanks!


I'm keeping the front struts on my existing van (about a year old) to swap onto my new van but the ones on my new van are up for grabs if you want them, (ledbury ones with a fair few miles on them). The hubs both have new bearings (4.5 inch pcd), but the hubs are still noisy so I'll not guarentee them. Driveshafts I'll be keeping for the project as they are refurbed recently.

i just thought u mite want a 76k diesel engine,i leave the engine on ebay.
back end i mite do a trailer out of it as it got refubed brakes and 15"alloys

[Guest]

114.3mm PCD, that sounds very large, I thought they were 100mm PCD on the Vans, is this corect? 114.3mm PCD? what alloys would fit that? would it be possible to take a look at an image to see if I could redrill a new PCD on them? im not too worried about the bearings, I would press some new ones in as a matter of course