Announcement
Collapse
No announcement yet.
1984 MG Montego EFi with digidash
Collapse
X
-
Carpet and trim in, Front passenger seat and seat belt stalk in, Aerial done, headliner finished as NOS A post finishers on. Rear door card started as drilled in the door ready to put on, unfortunately the central locking has stopped working so I have to sort that before attaching any door card. Last rear door seal found and on. I've been waiting many years to put that NOS Ashtray inLast edited by Jeff Turbo; 15th April 2020, 14:56.
- 1 like
-
Maybe John. Some forward, some backwards. One of the carpet trims is from a Maestro, so too small. Never noticed or even thought about it. Have now found the original and cleaned that up ready to go on. Lastly, the glove box hinge painting was going great till I ran out of black spray so used an old one i had, that reacted to the previous paint. Start again with thatLast edited by Jeff Turbo; 15th April 2020, 15:07.
- 1 like
Leave a comment:
-
Be a while before you get bored then! Coming on in leaps & bounds though..
Leave a comment:
-
Although it's near completed there is still quite a lot to do
Sort Aerial----DONE
Put rear carpet in----DONE
Attach all carpet plastic trims--DONE
Put seat belts, B post covers and stalks in----DONE
Put center console in----DONE
Under dash insulation----DONE
Steering column cover
Attach A pillar trims----DONE
Attach dash side trims and bolt covers---finally located
Clean drivers seat, rear bolsters and rear upright
Put seats in----passenger side done
Position Vin plate
Glove box lid and hinge
Check central locking
Attach outer door trims, wing tips--DONE
Attach Door mirrors--NEARSIDE DONE
Attach rear view mirror
Locate last rear door seal-----DONE
Drill holes for door cards
Attach door plastic insulation
Attach door cards
Oil probed ---DONE
Number plates----DONE
Check bulbs
Bleed brakes
Replace Steering wheel
Clear boot and put trim in
Put new jack etc in---located
Sort non working horn
Sort tracking
Shake down
MOT
Think thats all of itLast edited by Jeff Turbo; 17th April 2020, 12:34.
- 1 like
Leave a comment:
-
These are going on soon, nos door trims ready to go on, cleaned up the rear arch trims and just need to locate the front wing tips. also ordering a replacement number plate at some pointLast edited by Jeff Turbo; 14th April 2020, 15:59.
- 1 like
Leave a comment:
-
Steering wheels cleaned, i have two spare steering wheels and both now cleaned and ready for dye colouring. I will also have to dye of paint the seat beat covering topsLast edited by Jeff Turbo; 14th April 2020, 15:57.
- 1 like
Leave a comment:
-
Old front seat belts changing, and i've used a rear for the front after changing the inner mechanism.Last edited by Jeff Turbo; 14th April 2020, 15:56.
- 1 like
Leave a comment:
-
-
And been experimenting with an old sunvisor to find out if I can change the fabric colour, its not finished and very rough as i didn't mask anything up, but I believe i can do this if needed as the headlining is a little lighter.Last edited by Jeff Turbo; 12th April 2020, 12:51.
- 1 like
Leave a comment:
-
Finding all screws, handles and sunvisors in a bag. And they're all there. NOS aerial waiting to go on. There are also 2 types of sunvisor clips. The straight push in and the up and over. I will be putting those in as the straight push in kept coming out and they redesigned it, also the rear arch trims will need cleaningLast edited by Jeff Turbo; 12th April 2020, 12:55.
- 1 like
Leave a comment:
-
Glove box covers, one the looking mechanism doesn't work but the other does so I will swoop those over once I painted the hinge. also been cleaning the plastic trim and gear lever cap, just need the seatbelt top trim removed nextLast edited by Jeff Turbo; 12th April 2020, 12:57.
- 1 like
Leave a comment:
-
Oh yes John and it finally moves under its own steam, happy days but with only a handbrake that was exciting. Also been sorting various things for the interior. Aerial only has one hole so that to drill and tap. Thought I'd lost my original but found it later and luckily it has two screws. Door card steady brackets have now all been put on, taken awhile to find the gromits etc. and will have to remove again but I need them on for now to line up the door cardsLast edited by Jeff Turbo; 12th April 2020, 13:06.
- 1 like
Leave a comment:
-
That is a strange one! On the plus side, no gearbox removal and shiny new cv joints to go with the other hiny new bits....
Leave a comment:
Leave a comment: